Insights on How to Install a Truck Toolbox

A truck toolbox is essential for an individual who needs a piece of secure, lockable equipment to store their valuable truck tools. A truck tool box is uniquely designed to be anchored on a rig’s bed and offer maximum comfort to the user.

Over the years, people have shown interest in knowing the perfect way to install a truck toolbox. Toolboxes are easy to install provided you know how and where to purchase a toolkit suitable for your needs. Mounting a toolbox on your truck helps in protecting your valuables from theft and prevents your box from sliding around.

Toolboxes come in different shapes, sizes, materials, and designs. Plastic and non-metallic toolboxes are relatively cheap. However, they have some limitations, which include;

  • They may not withhold heavy tools.
  • They cannot withstand direct sunlight for an extended period.

Unlike the plastic or non-metallic toolboxes, the metallic toolbox can withstand heavy loads. You can follow this article to guide you on installing a truck toolbox.

How to Install Truck Toolbox

You may need the following tools before installing your toolbox;

  • Foam or padding material
  • A pair of pliers, screwdrivers, and spanner
  • Protective wear
  • Bolts, screws or nuts
  • A measuring tape
  • A truck toolbox

It is important to note that you should get high-quality materials when installing a toolkit. You should also purchase your nuts, bolts, and screws depending on the requirements to fit your toolbox in place.

Most of the supplies mentioned above can be purchased at local hardware stores.

Precaution Measures to Undertake Before Installing Your Tool Box

Ensure that you wear security glasses when using power tools.

  • You should get someone to assist you in lifting heavy weights, for example, the truck toolbox.
  • Check for the location of fuel tanks, electrical wires or lines before drilling holes on your car.
  • You may need bottom support for your truck box, or else its capacity and longevity will be minimal.

Step One: Identify the Installation Location

Before installing the toolbox, ensure that you take measurements of the box and spaces around it. Grab your measuring tape and record the correct box measurements.

You can then proceed to inspect your bed truck and get a perfect position to place your equipment.

Ensure that the location you pick gives your equipment freedom to open freely without hindrances from side rails. After getting the right location, proceed to the next step.

Step Two: Fitting the Foam Padding.

The padding step is a vital one; it is essential since it protects your truck cargo bay from potential damages. Padding also helps in preserving the paint of your truck.

Start by placing some rubber foam padding on the measured area before installing your toolbox.

Take the measurements of the box and then carefully place the box on the bed rail.

However, some trucks come with a bed liner; the liner helps in protecting your vehicle from any interference with the paint job or tear and wear. In case your car has a bed liner, you can skip this step for the next one.

Step Three: Align Your Tool Box with the Existing Holes

A truck’s cargo bay comprises of some holes on the bottom surface that are plugged with some rubber plugs.

Remove the plugs and align your toolbox in the right position. You can open the cover to ease the alignment of holes on the truck’s bed rail and holes on the box.

Step Four: Your J-Hooks or Any Other Types of Bolts You Have

Step 4 involves screwing the bolts on the aligned toolbox. Different trucks and toolboxes come with varying designs. You may need four to six bolts to fit your toolbox in place.

You can locate holes by lifting the cover on your truck. Below the bed rail, hook your j-bolts. You can use a pair of pliers to fit the nuts appropriately while using it ensures that you avoid putting maximum pressure.

For a plastic truck box, drill holes through it and tighten the appliance using bolts, screws or nuts.

Step Five: Tighten Your Tool Box to The Bed Rails.

As mentioned above, nuts are tightened by pliers, screwdrivers or spanners. Ensure that you use minimum pressure when tightening to avoid damaging the bed rail.

After you are done with fitting, ensure that you check if the toolbox is stable. Unstable tool boxes probably have some gaps between the toolbox and bed rail hence resulting in vibrations.

Step Six: Re-Confirm Your Job:

The final step is to examine your work and ensure that everything is in place. Ensure that you open the lid to check if it opens and closes without any restrictions.

You can also shake the toolbox to check if there is any movement. Lastly, you can confirm that no nuts, washers or bolts are left behind.

By following the steps above, you can easily install your truck toolbox in your car.

Tips On How to Install a Truck Tool Box

  • Ensure that you inspect your toolbox on a regular basis, check for any malfunction.
  • You can clean your toolbox to remove dirt, mud or debris.
  • Ensure that you do not fix your toolbox to your bed rail too tightly since it can cause damage to the truck’s bed rail.
  • Foam or padding sheets should have the same dimensions as the truck tool box.
  • Purchase nuts or bolts that are specifically designed to resemble an aluminum block that is easy to hook on to the rail.

Conclusion

In summary, from the content above one can learn about how to install a truck toolbox in their car using systematic and effortless steps explained above, it is evident that there are six easy procedures of anchoring a toolkit in your vehicle. Ensure that you locate your toolbox in the correct alignment.

Lastly, ensure that you check your toolbox regularly to inspect for any damages. You should also remember to fit your toolbox to avoid unnecessary movements properly. Regular check and management of devices in the toolbox lead to long lifespan with competent service.

Leave a Comment